Trailer Bunk and Roller Buying Guide: Bunks vs Rollers, Carpet vs Slides
Quick answer: Choose bunks if you launch at ramps with good water depth and want the best hull support, and rollers if you use shallow or steep ramps or load a heavy boat with little water under the trailer. Use 2x6 bunks for most boats over about 18 feet and 2x4 for smaller ones, keep the transom supported, and replace worn carpet with low friction slides or wrap to make loading easier.
The bunks and rollers on your trailer are the only parts touching the hull for every mile you tow. Set up well, they spread the boat's weight evenly, center it on the trailer and let it slide on and off without a fight. Set up badly, they cause hull dents, hooks near the transom, gelcoat scratches and frustrating ramp sessions. This guide covers bunk versus roller trailers, sizing bunk boards, carpet versus slick surfaces, keel and bow rollers, and fitting it all to your hull.
Step 1: Pick bunks or rollers for your ramps
| Factor | Bunk trailer | Roller trailer |
|---|---|---|
| Hull support | Excellent, weight spread along long boards | Good, weight on many small contact points |
| Water depth needed | More, boat must float on and off | Less, boat rolls on and off |
| Best ramps | Deep, moderate slope | Shallow, steep or tidal |
| Solo loading | Easy to drive on at a good ramp | Easy to winch on without much depth |
| Maintenance | Carpet or slides wear, boards can rot | Rollers crack and flat spot, more moving parts |
| Typical use | Fiberglass V hulls, center consoles, pontoons | Heavier boats at shallow ramps, some aluminum boats |
A boat that is hard to unload at your local ramp is often a sign the trailer style does not match the ramp, not that the trailer is broken.
Step 2: Size the bunk boards
- 2x4 bunks suit small aluminum boats, jon boats and lighter fiberglass boats.
- 2x6 bunks are the common choice for most fiberglass boats from about 18 feet up, spreading the load over more hull area.
- Use pressure treated lumber rated for ground contact and stainless or galvanized fasteners. Keep copper based treated wood from touching an aluminum hull directly; the carpet or a plastic slide acts as a barrier.
- Bunks should support the hull right up near the transom, where the engine weight sits. An unsupported stern can develop a hook in the bottom over time.
Step 3: Choose the bunk surface
- Bunk carpet: inexpensive and gentle on gelcoat, but it holds sand and grit, stays wet and grips the hull, making unloading harder in shallow water.
- Low friction slides: composite strips screwed to the top of the bunk. The boat slides on and off with much less winch effort, and channels flush grit away from the hull.
- Bunk wrap: a polymer sleeve that covers the whole board in place of carpet. Long lasting and slick, with end caps to finish the board.
Slick surfaces make the boat slide freely, so always attach the winch strap before pulling the trailer out and never unhook until the boat is in the water.
Step 4: Get the rollers right
- Keel rollers on the tongue guide the keel up the center. On bunk trailers they guide, while on roller trailers they carry load.
- Bow rollers and Y-stops sit on the winch post and stop the bow at the right spot.
- Wobble and bunk rollers on roller trailers pivot to match the hull shape.
- Match roller ID to the shaft (commonly 1/2 or 5/8 inch). Replace cracked, flat spotted or seized rollers, because a frozen roller drags and gouges the hull.
- Polyurethane and TPR rollers are softer and less likely to mark the hull than hard PVC.
Step 5: Fit and adjust to the hull
With the boat on the trailer, the bunks should sit flat against the hull along their full length, usually near the strakes on each side of the keel. The keel should just touch or sit slightly above the keel rollers on a bunk trailer. Position the bow stop so the boat sits with the correct tongue weight. Adjust brackets with the boat off the trailer, then recheck with the boat loaded. For the rest of the trailer, see our boat trailer parts buying guide.
Common bunk and roller mistakes
- Letting carpet wear through to bare wood or exposed staples that scratch the hull.
- Bunks stopping short of the transom, leaving engine weight unsupported.
- Ignoring cracked or seized rollers.
- Unhooking the winch strap early on slick bunks, letting the boat slide off on dry ramp.
- Power loading hard onto a roller trailer, which can damage rollers and the ramp.
Our picks for bunks and rollers
All in stock at Boat Supplies Direct.
Bunk wrap and slides
Caliber BunkWrap Kit 16 ft for 2x6 Bunks replaces carpet permanently, the 16 ft kit for 2x4 bunks suits smaller trailers, and Caliber Marine Slides 3 in x 15 in screw on over existing boards.
Bunk carpet
C.E. Smith Bunk Carpet 11 in x 12 ft for re-covering 2x4 or 2x6 boards, or the wider 18 in x 18 ft roll for longer bunks.
Keel and bow rollers
C.E. Smith 4 in Adjustable Keel Roller for 2 in Tongue, the C.E. Smith 4 in Bow Bell Roller, and the C.E. Smith Bow Y-Stop.
Roller bunks and replacement rollers
C.E. Smith 5 ft Roller Bunks support up to 1,500 pounds of well distributed weight for small boats at shallow ramps, and the C.E. Smith Ribbed Roller Replacement Kit refreshes worn rollers.
Brackets
C.E. Smith Vertical 90 Bunk Bracket 5 in x 8 in and the C.E. Smith 2 in Center Swivel Bracket for mounting and angling bunks.
Shop all trailer rollers, bunks and brackets →
Buying parts often? Get Dock Pass.
Free shipping on every order, 5% off eligible products and 60-day returns for $49 a year. See how Dock Pass works.
Frequently Asked Questions
Should I get a bunk or roller boat trailer?
Bunks give the best hull support and work well at ramps with good depth. Rollers make loading easier at shallow or steep ramps and with heavy boats.
What size boards are used for trailer bunks?
Most trailers use pressure treated 2x4 or 2x6 boards. 2x6 bunks spread the load better and are common on fiberglass boats over about 18 feet.
Are bunk slides better than carpet?
For ease of loading, yes. Low friction slides or bunk wrap let the boat slide on and off with less water and winch effort, and do not trap grit the way wet carpet does.
How far back should trailer bunks go?
Close to the transom, so the engine weight is supported. Bunks that stop well short can let the stern sag and create a hook in the hull bottom.
Should my keel touch the keel rollers?
On a bunk trailer, the keel should just touch or sit slightly above the rollers while the bunks carry the weight. On a roller trailer, the keel rollers carry load.
How often should I replace bunk carpet?
When it is worn thin, torn, or the staples or wood are exposed. Many owners switch to slides or bunk wrap to stop recarpeting.
This guide is general information. Follow your boat builder's and trailer manufacturer's support and adjustment recommendations, and have a trailer shop check setup if your boat does not sit correctly.


