Trailer Jack Buying Guide: Tongue Weight, Capacity and Wheel Types
Quick answer: Buy a trailer jack rated comfortably above your tongue weight, which on most boat trailers runs about 5 to 10 percent of the total loaded weight. A 1,000 to 1,200 pound swivel jack covers most trailers up to about 4,000 pounds loaded, a 1,500 pound jack suits trailers up to about 6,000 pounds, and heavier rigs need 2,000 to 2,500 pound jacks, often drop leg or flat foot styles. Use dual wheels for gravel or grass and a saltwater rated finish if you launch in salt.
The tongue jack does more work than most boaters realize. It lifts the coupler onto the ball, holds the trailer level in storage, and acts as the front wheel when you push the trailer around by hand. An undersized or rusted jack bends, binds or collapses, usually at the worst time. This guide covers sizing by tongue weight, mounting styles, wheel types and corrosion protection.
Step 1: Figure out your tongue weight
Tongue weight is the downward force the trailer puts on the hitch ball. Boat trailers typically run 5 to 10 percent of the combined weight of boat, engine, fuel, gear and trailer. The most reliable way to know is to measure it with a tongue weight scale or a bathroom scale and lever method for light trailers.
| Loaded trailer weight | Typical tongue weight | Recommended jack rating |
|---|---|---|
| Up to 2,000 lb | 100 to 200 lb | 1,000 lb |
| 2,000 to 4,000 lb | 200 to 400 lb | 1,000 to 1,200 lb |
| 4,000 to 6,000 lb | 300 to 600 lb | 1,500 lb |
| 6,000 to 10,000 lb | 400 to 1,000 lb | 2,000 to 2,500 lb, often flat foot or drop leg |
Size with margin. A jack that only just meets the tongue weight works hard, cranks stiffly and wears out fast. Remember that jack ratings assume a straight vertical load on firm ground.
Step 2: Choose the mounting style
- Bolt-on swivel: clamps to the tongue and swings up horizontal for towing. The most common boat trailer jack and the easiest to replace.
- Weld-on swivel: a permanent mount for steel trailers. Avoid welding on galvanized tongues without proper prep and ventilation.
- Fold-up or side mount: pivots out of the way and suits tongues where a swivel bracket will not fit.
- Drop leg: the inner leg drops down with a pin before cranking, so you skip most of the cranking on large height changes. Common on heavier trailers.
Step 3: Pick the foot or wheel
- Single wheel: standard for paved driveways and garage floors.
- Wide or dual wheel: spreads the load and rolls far better on gravel, grass and sand.
- Flat plate foot: best for heavier trailers parked on firm ground. Does not roll, so it will not creep. Add a jack pad on soft ground or asphalt in hot weather.
If you move the trailer by hand often, choose a wheel. If the trailer mostly sits parked and is moved by truck, a flat foot is more stable.
Step 4: Protect it from salt and rust
Most boat trailer jacks get dunked or splashed at the ramp. Zinc plated jacks are fine for fresh water. For saltwater launches, look for jacks with heavier corrosion resistant finishes, keep the jack swung up and clear of the water, rinse it with fresh water, and grease the gears and wheel axle periodically. A jack that grinds or binds is telling you it needs lubrication or replacement.
Step 5: Use it safely
- Chock the trailer wheels before unhitching or lifting.
- Always lock the swivel pin fully before cranking or towing; a half seated pin can let the jack fold under load.
- Swing the jack up and lock it before driving off. Dragging a jack is a common way to destroy one.
- Do not use the tongue jack to lift the trailer for a tire change. Use a jack made for that, and check your trailer bearings and hubs while the wheel is off.
Common trailer jack mistakes
- Buying on boat weight alone without considering engine, fuel and gear.
- Standard wheel on soft ground, which sinks and bends the jack.
- Towing with the jack down or the pin not fully engaged.
- Never greasing it after saltwater launches.
Our picks for trailer jacks
All in stock at Boat Supplies Direct.
Saltwater trailers
Powerwinch Saltwater Series 1,500 lb Bolt-On Jack with a finish built for salt spray, or the 1,000 lb Saltwater Series for lighter trailers.
Everyday swivel jacks
C.E. Smith 1,000 lb Trailer Swivel Jack for small boats, and the Powerwinch Select Series 1,200 lb Bolt-On Jack for mid size rigs.
Soft ground
Powerwinch Select Series 1,500 lb Double Wheel Jack and the Attwood Fold-Up 1,500 lb Dual Wheel Jack roll easily on gravel and grass.
Heavy trailers
C.E. Smith 2,500 lb Drop Leg Trailer Jack speeds large height changes, and the Powerwinch Saltwater 2,500 lb Flat Plate Jack holds heavy tongues steady.
Accessories and dollies
Safe-T-Alert Heavy Duty Jack Stand Pad keeps a jack from sinking, and the C.E. Smith 250 lb Outboard Motor Dolly moves small outboards around the shop.
Shop all trailer jacks and dollies →
Buying parts often? Get Dock Pass.
Free shipping on every order, 5% off eligible products and 60-day returns for $49 a year. See how Dock Pass works.
Frequently Asked Questions
What size trailer jack do I need for my boat?
One rated well above your tongue weight, which is usually 5 to 10 percent of the total loaded trailer weight. A 1,000 to 1,500 pound jack covers most small and mid size boat trailers.
How do I find my trailer's tongue weight?
Measure it with a tongue weight scale at hitch height with the boat loaded as you tow it. Estimates based on percentages are only a starting point.
Is a dual wheel trailer jack better?
On gravel, grass or sand, yes. Dual or wide wheels spread the load and roll more easily. On pavement a single wheel is fine.
What is a drop leg trailer jack?
A jack whose inner leg drops down and pins in place before cranking. It saves cranking on large height changes and is common on heavier trailers.
Can I use my tongue jack to change a trailer tire?
No. The tongue jack lifts the coupler, not the axle. Use a jack designed for tire changes and chock the other wheels.
How do I keep a trailer jack from rusting?
Keep it swung up out of the water when launching, rinse it with fresh water after saltwater use, and grease the gears and wheel periodically.
This guide is general information. Follow your trailer and jack manufacturers' ratings and instructions, and never exceed the jack's rated capacity.


