Livewell Pump Buying Guide: GPH Sizing, Fill vs Recirculation and Plumbing
Quick answer: Size your livewell pump to the well: about 500 GPH for wells up to 20 gallons, 800 to 1,100 GPH for 20 to 40 gallons, and 1,100 to 1,600 GPH or dual pumps for 40 gallons and up. Plan on real flow of roughly 60 to 70 percent of the rated GPH once hose and lift are involved, and aim to exchange the full well volume every few minutes. Most boats fishing live bait do best with two pumps: a fill pump on a thru-hull pickup and a separate recirculating aerator.
Dead bait is wasted money and wasted fishing time. Bait dies in a livewell for three reasons: not enough oxygen, water that gets too warm or dirty, and too much turbulence that batters fragile baits. The right pump, sized correctly and plumbed with a proper overflow, solves all three. This guide covers sizing, fill versus recirculation pumps, plumbing and the setup mistakes that kill bait.
Step 1: Size the pump to your well volume
Start with the volume of the well, not the size of the boat. Builders list well capacity in gallons, or you can measure length by width by water depth in inches and divide by 231.
| Livewell size | Fill pump (rated GPH) | Approx. full exchange at rated flow | Typical use |
|---|---|---|---|
| Up to 20 gal | 500 | About 2.5 minutes | Bay boats, flats skiffs, shrimp and small baitfish |
| 20 to 30 gal | 800 | About 2 minutes | Center consoles, mixed inshore baits |
| 30 to 40 gal | 1,100 | About 2 minutes | Pilchards, threadfins, pinfish |
| 40 gal and up | 1,500 to 1,600, or two pumps | About 2 minutes | Offshore boats, large baits, big loads of bait |
Real flow after hose, fittings and lift will stretch those exchange times by a third or more. That is still fine for most baits. Delicate, high-oxygen baits such as pilchards, greenbacks and threadfin herring want the high end of the range. Shrimp and hardy baits like pinfish do well with less.
Step 2: Fill pump, recirculating aerator, or both
- Fill pump: mounted on a thru-hull pickup below the waterline, it pulls fresh seawater into the well. Fresh water carries oxygen and flushes waste. Thru-hull livewell pumps with a removable cartridge let you swap the motor without hauling the boat.
- Recirculating aerator: mounted on a fitting in the bottom or side of the well, it pulls water from the well and sprays it back in. It adds oxygen without bringing in new water, which matters at anchor in dirty water, when surface water is very hot, or when you are running offshore and the pickup is aerated.
- Best setup: one fill pump plus one recirculating aerator on separate switches. Run fill when the water outside is good, switch to recirculation when it is not, and run both when the well is packed.
Step 3: Match the pickup and plumbing
- Most livewell pumps are centrifugal and not self-priming. Mount the fill pump below the waterline so water reaches it by gravity, and use a forward-facing or angled pickup so it does not draw air underway.
- Pick the inlet style that fits your hull: straight thru-hull, angled thru-hull, or a seacock inlet so you can close the intake if a hose fails. Our thru-hull fitting guide covers safe installs below the waterline.
- Use the hose size the pump outlet calls for, commonly 3/4 inch or 1-1/8 inch, and double-clamp every connection below the waterline.
- Size the overflow larger than the fill line, so the well cannot overfill and flood the boat. A standpipe overflow also sets the water level in the well.
Step 4: Control flow so you do not beat up the bait
Too little flow and bait suffocates. Too much flow aimed straight at the bait tires them out and knocks off scales. Point the inlet so water circulates around the well, use a spray head or aerator head to break up the stream, and add a fill valve so you can dial flow down for shrimp or up for pilchards. Round or oval wells keep bait swimming instead of piling into corners.
Step 5: Wire it on its own circuit
Give each pump its own fused circuit and helm switch, sized for the pump's amp draw and run length. Use tinned marine wire and sealed connections, since livewell pumps live in a wet, salty space. Our wire and terminal guide walks through gauge and crimps. A livewell timer is a good add-on for long days, since it cycles the pump to save battery while keeping water fresh.
Common livewell pump mistakes
- Undersized pump for the well, especially after adding a larger tank or carrying delicate bait.
- Mounting a non-self-priming pump above the waterline, so it runs dry and never moves water.
- Overflow smaller than the fill line, which floods the well and the boat.
- No recirculation option, forcing you to pump in hot or dirty surface water at anchor.
- Ignoring the pickup. A clogged strainer or grass in the thru-hull cuts flow to a trickle.
Our picks by setup
All in stock at Boat Supplies Direct.
Fill pumps for small to mid-size wells
Rule 500 GPH Livewell Pump, Angled Thru-Hull for wells up to 20 gallons, or the Rule 800 GPH Livewell Pump, Straight Thru-Hull for 20 to 30 gallon wells. Both use a replaceable cartridge motor.
Fill pumps for larger wells
Rule 1100 GPH Livewell Pump, Straight Thru-Hull for 30 to 40 gallons, and the Rule Tournament Series 1600 GPH Dual Port for large wells or feeding two wells from one pickup.
Seacock inlet for peace of mind
Rule 500 GPH Livewell Pump, Straight Seacock Inlet lets you close the intake without pulling the boat.
Recirculating aerators
Attwood Tsunami T800 Aerator for mid-size wells, the Johnson Pump Aqua O2 Twin Port 800 GPH to feed two outlets, or the Shurflo Bait Sentry 1100 Magnetic Drive for larger wells.
Self-priming and replacement parts
Shurflo Pro Baitmaster II is a self-priming pump for portable tanks and wells that cannot use a below-waterline pickup. Keep a spare Rule 1100 GPH Replacement Cartridge aboard, and add a Shurflo Livewell Fill Valve to control flow.
Buying parts often? Get Dock Pass.
Free shipping on every order, 5% off eligible products and 60-day returns for $49 a year. See how Dock Pass works.
Frequently Asked Questions
What size livewell pump do I need?
Match rated GPH to well volume: about 500 GPH for wells up to 20 gallons, 800 to 1,100 GPH for 20 to 40 gallons, and 1,100 GPH or more, or two pumps, for larger wells.
How often should livewell water turn over?
Aim to exchange the full well volume every few minutes. Delicate baitfish like pilchards need faster turnover than shrimp or pinfish.
Do I need a separate recirculation pump?
Yes if you fish at anchor, in dirty water, or when surface water is very hot. A recirculating aerator adds oxygen without pulling in new water.
Why is my livewell pump not pumping water?
Most livewell pumps are not self-priming, so an air lock, a pump mounted above the waterline, or a clogged pickup will stop flow. Check the pickup and make sure the pump sits below the waterline.
Can I replace just the motor on a cartridge livewell pump?
Yes. Cartridge-style pumps let you twist out the motor and install a replacement cartridge while the base stays in the hull.
Can a bilge pump be used as a livewell pump?
It is not recommended. Livewell pumps are built for continuous duty and come with the right inlet fittings, while bilge pumps are designed for intermittent use.
This guide is general information. Follow your boat builder's and pump manufacturer's instructions, use ABYC practice for below-waterline fittings and wiring, and check local regulations on bait collection and possession.


