Bass Boat Upgrades Worth the Money: Jack Plates, Sonar, Livewells and Charging

By Boat Supplies Direct·Updated Nov 18, 2026·7 min read

Bass boat with trolling motor and jack plate tied to a dock on a foggy lake at sunrise

Quick answer: The bass boat upgrades that pay off the most are the ones that put you on more fish and keep you fishing longer: a hydraulic jack plate for shallow running and better hole shot, forward-facing or imaging sonar on the trolling motor, a healthy livewell pump, and an onboard battery charger sized to your trolling motor batteries. Fix charging and the livewell first, then spend on electronics and the jack plate.

Most bass boats leave the factory with a basic package. The hull and outboard are usually fine, but the electronics, charging and rigging are built to hit a price. Winter is the best time to upgrade: the boat is out of the water, dealers and riggers are less busy, and everything is installed and tested before the spring bite. This guide ranks the upgrades by how much they change your day on the water, explains what to look for in each, and points out the mistakes that waste money.

Step 1: Get charging and power right first

Nothing ends a tournament day faster than a trolling motor that dies at 1 p.m. Before you add a single new graph, make sure the power system can support it.

  • Onboard charger: a waterproof, multi-bank charger lets you plug in one cord at home and charge every battery properly. Match the bank count to your batteries. A 24V trolling motor plus a cranking battery needs 3 banks. A 36V trolling motor plus cranking needs 4.
  • Amps per bank: 10 to 15 amps per bank is a solid range for typical deep cycle batteries so they recharge overnight.
  • Battery condition: old flooded batteries lose capacity fast. If yours are more than 3 or 4 seasons old, test them before blaming the trolling motor.
  • Lithium: if you switch to lithium, confirm your charger has a lithium profile that matches the battery maker's specs.

Our battery charger guide and marine battery guide go deeper on sizing and chemistry.

Step 2: Upgrade your sonar where it matters

Electronics are where most anglers see the biggest jump in fish caught. The key is putting the right sonar in the right place.

Upgrade What it does Best for
Bigger console graph Larger screen for mapping, side and down imaging while running Finding structure and contour lines
Bow graph Puts sonar and mapping where you actually fish Anyone who spends the day on the trolling motor
Forward-facing sonar Live view of fish and lures in front of the boat Suspended fish, brush piles, docks, open water
Trolling motor transducer mount Keeps the transducer aimed where the motor points Any bow sonar setup

Forward-facing units draw real power and need a solid mount. Run the transducer cable cleanly along the trolling motor shaft so it does not chafe when you stow and deploy. Our fishfinder and transducer guide and chartplotter combo guide cover screen size and sonar types.

Step 3: Add a hydraulic jack plate

A jack plate lets you raise or lower the outboard from the helm. On a bass boat that does three useful things:

  • Shallow water running: raise the motor to idle or run through skinny water and over grass without dragging the lower unit.
  • Top end and efficiency: raising the engine reduces drag from the gearcase once the boat is on plane.
  • Hole shot: lower the motor for a strong launch, then raise it as you come up to speed.

Setback (how far the plate moves the motor behind the transom) affects handling. Many bass boats run 6 to 10 inches. More setback lets you raise the motor higher but can make the bow lighter. Check your boat builder's recommendation and your outboard's weight before choosing. A jack plate gauge at the helm shows the motor height so you can repeat your best setting. See our jack plate guide for setback and installation details.

Step 4: Keep the livewell healthy

In tournaments, a dead fish costs you weight. Even fun fishing, a good livewell means fish go back healthy. Upgrade points:

  • Pump GPH: most bass boat livewells use pumps in the 500 to 1,100 GPH range. Match the replacement to your boat's plumbing and nozzle length.
  • Timer or recirculation: run recirculation in hot weather to keep oxygen up without pulling warm surface water.
  • Spare pump: livewell pumps are cheap and fail at the worst time. Carry one.

Our livewell pump guide explains fill vs recirculation plumbing.

Step 5: Small upgrades that make a big difference

  • Trolling motor handle or pull: makes stowing and deploying easier, especially in rough water.
  • Weedless prop: cuts down on fouling in grass and pads.
  • Trolling motor remote: lets you steer from anywhere on the deck if your motor supports one.
  • Keel guard and trailer keel rollers: protect the hull when loading at shallow ramps. Our bunk and roller guide covers setup.

Common bass boat upgrade mistakes

  • Adding graphs without upgrading power. New electronics on weak batteries leads to low voltage alarms and resets.
  • Undersized wiring. Use the right gauge for trolling motor and graph runs. Voltage drop kills performance.
  • Too much setback for the hull. Follow the builder's recommendation.
  • Mixing battery types or ages in a trolling motor bank. Replace them as a set.
  • Skipping the test run. Water test every upgrade before your first tournament.

Our picks for bass boat upgrades

All in stock at Boat Supplies Direct. Confirm fit with your boat, motor and electronics before ordering.

Hydraulic jack plates

Bob's Machine 6" Setback Action Series Hydraulic Jack Plate (Gloss Black): a popular setback for many bass hulls. For heavier outboards, look at the T-H Marine ATLAS EDGE 6" Heavy Duty Hydraulic Jack Plate.

Jack plate gauge

Bob's Machine LED Jack Plate Gauge shows engine height at the helm so you can repeat your best setting.

Console graph

Garmin ECHOMAP UHD2 74sv Combo (Remanufactured): 7" chartplotter and fishfinder with a transducer included. It ships with U.S. coastal maps, so freshwater anglers may want to add lake mapping.

Trolling motor sonar mount

Lowrance ActiveTarget Trolling Motor Shaft Mount for anglers running Lowrance ActiveTarget forward-facing sonar.

Onboard battery charger

ProMariner ProNautic 1215P 15 Amp 3 Bank Charger: a good match for a 24V trolling motor setup plus a cranking battery.

Livewell pump

T-H Marine HYDRA 800 GPH Livewell Pump (Long Nozzle) as a replacement or spare. Check nozzle length against your current pump.

Trolling motor accessories

Bob's Machine The Big D Trolling Motor Handle for easier stowing, and the Lowrance Weedless Prop for Ghost Trolling Motors for grass-heavy lakes.

Shop all bass and fishing boat gear →

Buying parts often? Get Dock Pass.

Free shipping on every order, 5% off eligible products and 60-day returns for $49 a year. See how Dock Pass works.

Frequently Asked Questions

What is the first upgrade I should make to a bass boat?

Start with power: healthy batteries and a properly sized onboard charger. Every other upgrade, from graphs to the trolling motor, depends on good voltage.

Is a jack plate worth it on a bass boat?

For most anglers, yes. It lets you run shallower water, improves hole shot, and can add top end. The benefit is largest on boats that fish shallow lakes, rivers and grass.

How much setback do I need on a jack plate?

Many bass boats run 6 to 10 inches, but the right number depends on the hull and outboard weight. Follow your boat builder's recommendation.

Do I need forward-facing sonar?

It is not required to catch bass, but it helps a lot with suspended fish and offshore structure. Make sure your batteries and charging can handle the extra draw first.

How many banks should my battery charger have?

One bank per battery. A 24V trolling motor plus a cranking battery needs 3 banks, and a 36V system plus cranking needs 4.

Can I install these upgrades myself?

Livewell pumps, trolling motor accessories and charger installs are reasonable DIY jobs if you are comfortable with marine wiring. Jack plates involve transom bolts and outboard weight, so many owners have a qualified rigger handle them.

This guide is general information. Check your boat builder's and engine manufacturer's specifications for jack plate setback, transom ratings, wiring gauge and battery requirements, and follow each product's installation instructions. When in doubt, use a qualified marine technician.

For sourced data on what it costs to own, maintain and equip a boat, see our boat ownership cost statistics.